Spyder MR2
Spyder MR2 - Spyder Paintball Gun
The MR2 looks like it'll live up to its hype. It has the stock features to outperform mechanical scenario markers like the JT TAC-5 and low-end electronic mil-sim markers like the US-5. No eyes, but the construction and fire rate put it on par with (if not beyond) the Smart Parts SP-8. The overview:
MR2 BARREL - 12" ported barrel with no muzzle break. Matte black so there's no glare to give away your position. Not the quietest, but that's Kingman for you. Good internal finish, and better accuracy than average for a stock barrel. Replacement barrels will be difficult to use - the back 2 inches of the barrel fit tightly into the shroud that takes the place of a volumizer, so barrels like the CMI / Thunder Pig Tru-Flight will work but barrels that "fatten" at the base won't, such as the Smart Parts Progressive.
FOREGRIP / EXPANSION CHAMBER - Foregrip is very tough plastic, probably the only large non-metal piece of the marker. It acts as a mini expansion chamber, so it's not just a gas-through foregrip. No way to add a reg on this end. Grip is angled 15 degrees forward. Grip material is matte-finish black plastic but isn't slick or hard to hold. Foregrip is as thick and wide as the trigger frame.
VOLUMIZER - Volumizer is replaced by a volumizer housing extending 2" from the front of the body. Essentially, everything forward of the body and under the foregrip is the volumizer. Interesting design!
TRIGGER / FRAME - The switch is a paddle switch, not a micro-button; should still be replaceable easily. Trigger pull is a hair under 1/2" (the first 1/4" is slack) but is adjustable externally via set screw on the blade trigger. Frame is all metal with flexible but slick grips. Uses a standard 9.6v JAVA rechargeable battery. A switch on the rear of the grip flips between single, 3-burst, and auto, indicated with a single 3-color LED - no way to adjust auto fire rate. Tournament semi-only lock is accomplished with a jumper on the board. There is no safety. The only hopper I have is a 12BPS Ricochet AK, so I'll have to be careful.
DROP / ASA - ASA works well enough and has an internal filter. Drop is short but angled. BIG HOORAY: The MR series uses IN-LINE SCREWS ON THE DROP FORWARD!!! No more offset Kingman-only holes! The line is black-coated stainless braided line.
DETENT - Integrated under the angled feed port's braces. Not a standard Kingman left-side ball-bearing.
BODY - Minimal milling. Feedneck is an angled 45-degree stub with a cheap plastic adapter/elbow. Field stripping is a standard Kingman pull pin (held by a ball bearing, not a cotter pin). Body is all metal, so this thing weighs several tons. The top of the marker comes with built-in 7/8" Weaver rails, while the carry handle (removeable) is topped with a 3/8" dovetail mount. Carry handle is too short to be used for carrying. Most rails and the exterior shrouds can be removed. Body is uniformly matte black with a tough finish.
STOCK - Shared with the MR1. Stock is open-frame skeletal design but is very stable and tough. Makes the already heavy MR2 even more of a pig, but it's worth it. The stock insertion is o-ringed so the marker may perform even better with it than without.
INTERNALS - Top-cocking marker (stacked-tube blowback) with an open
rear end (unless the stock is attached). The snap-back cocking system eliminates
the exposed cocking knob, so effectively it's a flush-cocker. Internals may
be shared with the TLX, TL-R, and Sonix Value / Sonix Pro, but I'm not 100%
certain yet. BONUS: the MR2 comes stock with a top-cocking version
of the Kingman Delrin ACS bolt! Works very well. Interior finish is excellent.
Velocity is adjusted via a rear set screw, not by the old Kingman thumbwheel.
We highly reccommend the two options for your paintball gun. The first is
a Nitrogen Tank
and the other is the Empire Reloader B
Purchase the Spyder MR2 Here
